How to order Contact us Distributors Reviews
Register / Login

Select currency

If you'd like to view estimated pricing in other currencies then please select a currency below below.

GBP USD EUR JPY AUD NOK CHF NZD CAD

Please note:

  • Currency conversions are estimates and for information only
  • Your order will be billed in GBP
  • All prices exclude VAT / other local sales taxes
  • Shipping calculated during checkout


PowerBoost 1000 Charger - Rechargeable 5V Lipo USB Boost @ 1A - 1000C

by Adafruit
An image of PowerBoost 1000 Charger - Rechargeable 5V Lipo USB Boost @ 1A - 1000C An image of PowerBoost 1000 Charger - Rechargeable 5V Lipo USB Boost @ 1A - 1000C An image of PowerBoost 1000 Charger - Rechargeable 5V Lipo USB Boost @ 1A - 1000C An image of PowerBoost 1000 Charger - Rechargeable 5V Lipo USB Boost @ 1A - 1000C

PowerBoost 1000C is the perfect power supply for your portable project!

With a built-in load-sharing battery charger circuit, you'll be able to keep your power-hungry project running even while recharging the battery! This little DC/DC boost converter module can be powered by any 3.7V LiIon/LiPoly battery, and convert the battery output to 5.2V DC for running your 5V projects.

If you dont need the 1A battery charger, smart load-sharing, or 1A iOS resistors, check out the Powerboost 500C

Adafruit tweaked the output to be 5.2V instead of a straight-up 5.0V so that there's a little bit of 'headroom' for long cables, high draw, the addition of a diode on the output if you wish, etc. The 5.2V is safe for all 5V-powered electronics like Arduino, Raspberry Pi, or Beagle Bone while preventing icky brown-outs during high current draw because of USB cable resistance.

The PowerBoost 1000C has at the heart a TPS61090 boost converter from TI. This boost converter chip has some really nice extras such as low battery detection, 2A internal switch, synchronous conversion, excellent efficiency, and 700KHz high-frequency operation. Check out these specs!

  • Synchronous operation means you can disconnect the output completely by connecting the ENable pin to ground. This will completely turn off the output
  • 2A internal switch (~2.5A peak limiting) means you can get 1000mA+ from a 3.7V LiPoly/LiIon battery. Just make sure your battery can handle it!
  • Low battery indicator LED lights up red when the voltage dips below 3.2V, optimized for LiPo/LiIon battery usage
  • Onboard 1000mA charge-rate 'iOS' data resistors. Solder in the USB connector and you can plug in any iPad, iPhone or iPod for 1000mA charge rate.
  • Full breakout for battery in, control pins and power out
  • 90%+ operating efficiency in most cases (see datasheet for efficiency graphs), and low quiescent current: 5mA when enabled and power LED is on, 20uA when disabled (power and low batt LED are off)

To make this even more useful, they stuck a smart load-sharing Lipoly charger on the other side. The charger circuitry is powered from a microUSB jack, and will recharge any 3.7V/4.2V LiIon or LiPoly battery at 1000mA max rate. There's two LEDs for monitoring the charge rate, a yellow one tells you its working, a green one lights up when its done.

Since the built-in battery charger has load-sharing, it will automatically switch over to the USB power at the Micro USB input when available, instead of continuously charging/draining the battery. This is more efficient, and lets you charge-and-boost at the same time without any interruption on the output so its fine for use as a "UPS" (un-interruptable power supply).

Just be aware that the charge rate is 1000mA max, and there's some inefficiency during the boosting stage, so make super sure that the USB adapter you're using to charge with is high quality, can supply 2A and has thick power wires. Lower quality ones will not act well due to the voltage drop on the wires or droop on the power supply. This is especially true if you're actually drawing 1000mA out of the PowerBoost 1000C, the MCP73871 maxes out at 1.8A. You do have to always have a LiPo plugged into manage the load spikes, it's not optional!

This charger-booster is great for powering your robot, Arduino project, single-board-computer such as Raspberry Pi or BeagleBone! Each order comes with one fully assembled and tested PCB and a loose USB A jack. If you are powering your project from USB, solder the USB A jack in (a 3-minute soldering task). If you would like to use a terminal block, solder a 3.5mm 2pin block to the output spot where the USB jack would go. Or dont solder anything in for a more compact power pack.

Reviews

User photos

PowerBoost 1000C is the perfect power supply for your portable project!

ADA2465

You must register for an account and be logged in to view pricing or place an order on the Pimoroni Wholesale store.

If you represent a school or university, a business, or reseller of Maker products then you can sign up for a wholesale account.

If you already have an account you can login to your account here.

Alternatively the easiest way to get your hands on the products we offer is to order them directly from our customer facing online store.

SKU
ADA2465
EAN
0704256791445
Brand
Adafruit
Stock available
0 units
Backorder not allowed on this product
Weight
9g

Video introduction

Guides & tutorials

Search

 

Region

Your search returned no results.

Subscribe

We'll keep you up to date with new product launches!

The good ship

We've been sailing the Maker seas offering our wares since 2012.

  • read about our history
  • what our customers say
  • find a local distributor
  • contact our business team

We manufacture all of our products locally at our workshop in Sheffield, UK

Under one roof

Pimoroni are your one-stop shop for bulk and education purchasing of Raspberry Pi, Pimoroni, micro:bit, Adafruit, Sparkfun, and many other brands.

If you have any questions about what we offer then drop us a line.

Pimoroni Ltd

Unit 1, Parkway Business Park,
Parkway Drive,
Sheffield,
S9 4WN,
United Kingdom

Registered in England and Wales:
Company №: 07510759
VAT Reg №: GB 140 8707 21